Driver sd needs updating please use bustype methods gentoo

However, the second one does not seem to be recognized at all.In /dev, I can see only one instance of /dev/cdrom, /dev/dvd, /dev/sr0, which in all cases map my first DVD drive when I mount.They are run by the udev service and the service is blocked until the script returns, so you may wreck your udev service if your script takes too long. The first one is recognized as /dev/sr0 and works properly.device: 'mmc.0': device_add bus: 'platform': add device mmc.0 bus: 'mmc': registered device class 'mmc_host': registering Driver 'mmcblk' needs updating - please use bus_type methods bus: 'mmc': add driver mmcblk bus: 'platform': add driver dw_mmc bus: 'platform': add driver dwmmc_adi bus: 'platform': driver_probe_device: matched device mmc.0 with driver dwmmc_adi bus: 'platform': really_probe: probing driver dwmmc_adi with device mmc.0 pinctrl-adi2 pinctrl-adi2.0: found group selector 21 for mmc0grp pinctrl-adi2 pinctrl-adi2.0: request pin 76 (PE12) for mmc.0 pinctrl-adi2 pinctrl-adi2.0: request pin 77 (PE13) for mmc.0 pinctrl-adi2 pinctrl-adi2.0: request pin 78 (PE14) for mmc.0 pinctrl-adi2 pinctrl-adi2.0: request pin 79 (PE15) for mmc.0 pinctrl-adi2 pinctrl-adi2.0: request pin 80 (PF0) for mmc.0 pinctrl-adi2 pinctrl-adi2.0: request pin 81 (PF1) for mmc.0 pinctrl-adi2 pinctrl-adi2.0: request pin 82 (PF2) for mmc.0 pinctrl-adi2 pinctrl-adi2.0: request pin 83 (PF3) for mmc.0 pinctrl-adi2 pinctrl-adi2.0: request pin 87 (PF7) for mmc.0 pinctrl-adi2 pinctrl-adi2.0: request pin 84 (PF4) for mmc.0 pinctrl-adi2 pinctrl-adi2.0: request pin 44 (PC12) for mmc.0 dwmmc_adi mmc.0: num-slots property not found, assuming 1 slot is available dwmmc_adi mmc.0: obtain a copy of previously claimed pinctrl dwmmc_adi mmc.0: IDMAC supports 32-bit address mode. dwmmc_adi mmc.0: Version ID is 270a dwmmc_adi mmc.0: DW MMC controller at irq 73, 32 bit host data width, 1024 deep fifo dwmmc_adi mmc.0: No vmmc regulator found dwmmc_adi mmc.0: No vqmmc regulator found dwmmc_adi mmc.0: GPIO lookup for consumer wp dwmmc_adi mmc.0: using device tree for GPIO lookup of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/scb/[email protected][0]' of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/scb/[email protected][0]' dwmmc_adi mmc.0: using lookup tables for GPIO lookup dwmmc_adi mmc.0: lookup for GPIO wp failed mmc_host mmc0: card is non-removable.

'Hot-plugging' means inserting/removing a drive while a computer is turned on.I would like to know how I should setup Gentoo so that I can use both my DVD drives. [email protected] /wine/utorrent/drive_c/u Torrent $ dmesg | grep -i sr [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.677257] Driver 'sr' needs updating - please use bus_type methods [ 2.093813] sr0: scsi3-mmc drive: 125x/48x writer dvd-ram cd/rw xa/form2 cdda tray [ 2.094493] sr 3:0:0:0: Attached scsi CD-ROM sr0 [ 2.094580] sr 3:0:0:0: Attached scsi generic sg0 type 5 I forgot to mention, in the BIOS my "non-detected" drive is the bootable DVD drive.Both drives are recognized in the BIOS, therefore the issue is clearly software related, and not hardware related. Hence Gentoo was installed from this drive and the installation went flawlessly. I build with no modules, but do have modules enabled due to n Vidia.And somebody please fix the "Driver 'sd' needs updating - please use bus_type methods" above.

Search for driver sd needs updating please use bustype methods gentoo:

driver sd needs updating please use bustype methods gentoo-45driver sd needs updating please use bustype methods gentoo-63driver sd needs updating please use bustype methods gentoo-87

Leave a Reply

Your email address will not be published. Required fields are marked *

One thought on “driver sd needs updating please use bustype methods gentoo”